Part Time Switch Module Replacement 50mA Control Cycle DC 5V~36V Durable

Description

Product Description
Part Time Switch Module Replacement 50mA Control Cycle DC 5V~36V Durable
Features:
100% brand new and high quality
Made of high-quality materials, durable
In order to realize a fast high-frequency switching circuit, the number of switching times is not limited.
There is no noise, no sparks and no electromagnetic interference during the opening/closing process.
Compared with ordinary electromagnetic relay modules, it has a longer service life.
Dual MOS parallel active output, low internal resistance, high current, high power; at room temperature, the working current is up to 15A, and the power is up to 400W, which can be used in most devices.
The wide voltage input from 5V to 36V is usually used to control DC motors, lights, LED strips, micro pumps, solenoid valves, etc., which is very convenient.
It has an emergency stop function ("STOP" button) and reverse input protection.
If no operation is performed within 5 minutes, it will automatically enter sleep mode and turn off the display, and then press any button to wake it up.
You can set different OP, CL, LOP parameters, which are of each other and saved separately.
In the event of a power failure, all parameter settings will be automatically saved.
Product parameters:
Voltage: DC 5V~36V
Trigger signal source: high level trigger (3.0V~24V), signal ground and system ground are not on the common ground to improve the anti-interference ability of the system (you can also connect them to the common ground).
Output capacity: DC 5V~36V, continuous current is 15A at room temperature, power is 400W. With the enhanced heat dissipation function, the current can be as high as 30A.
Quiescent current: 20mA
Working current: 50mA
Working temperature: -40℃~85℃
Clock (time delay) range: 0.1 second to 999 minutes
Size: 60 * 34 * 12mm / 2.36 * 1.33 * 0.47"
Instructions:
Operation mode:
P1: Trigger signal, the relay is in the "OP" time, and then disconnected; in the "OP" time, as follows:
P1.1: The signal is triggered again, invalid
P1.2: Trigger the signal again, reset the clock
P1.3: The signal is triggered and reset again, the relay is turned off and the timing is stopped;
P-2: Trigger signal, the relay is turned off for "CL" time, the relay is turned on for "OP" time, and the relay is turned off after timing;
P3.1: Trigger signal, the relay opens after the "OP" time, the relay closes the "CL" time, and then runs the cycle; if the signal is triggered again in this cycle, the relay is disconnected and the timing stops; the number of cycles can be set (" LOP").
P3.2: There is no trigger signal after power-on, the relay is turned on for "OP" time, and the relay is turned off for "CL" time, and then cyclically runs; the number of cycles ("LOP") can be set.
P-4: Signal hold function. If there is a trigger signal, the clock will be reset and the relay will remain on; when the signal disappears, the relay will be turned off after timing the "OP" time; if another signal is triggered during the timing, the timing will be reset.
How to set the clock range:
After setting the parameter value in the mode selection, press the "STOP" button to set the clock range;
XXX. The last decimal point lights up, and the range is from 1 second to 999 seconds.
XX. The second to last decimal point of X lights up, the range: 0.1 second to 99.9 seconds
X. X. X. All 3 decimal points are lit, range: 1 minute to 999 minutes.
For example, if you want to set "OP" to 3.2 seconds, please light up the penultimate decimal point and set the digital display to 03.2.
Parameter description: "OP"-on time, "CL"-off time, "LOP"-number of cycles (1-999 times, "---" stands for infinite loop).
These parameters are of each other, but shared by each mode. For example, in P1.1 mode, set the opening time "OP" to 5 seconds, if you switch to P1.2 mode, its "OP" will also be 5 seconds.
In the main interface (display 000), press the "SET" button to display "OP" ("CL", "LOP") and the corresponding time XXX;
If the mode (such as mode P1.1, P1.2, P1.3) only has "OP" time, press "SET" key to display only "OP" and the corresponding time; otherwise, only "OP" time will be displayed.
Some models (such as mode P3.1, P3.2) have parameters "OP", "CL", "LOP", pressing the "SET" button will display "OP" and the corresponding time, "CL" and the corresponding time Time, "LOP" and corresponding times;
After setting the mode, press the "SET" key in the main interface to view the information about the current mode parameters, which is very convenient.
How to set the parameters:
1. First, read the instructions to determine the desired mode of operation.
2. Power on the module, display the current working mode (P1.1 default mode), and then enter the main interface; press and hold the "SET" key for 2 seconds to enter the mode selection interface. Then press the "UP" and "DOWN" buttons to select the mode (P1.1~P-4).
3. Select the mode (such as P3.2), and then press the "SET" button, the parameter to be set flashes ("OP" open time, "CL" closed time, "LOP" cycle ("- "" means infinite Cycle)), press (or hold) the "UP" and "DOWN" buttons to adjust the parameter value; then press the "stop" button to set the decimal point to select the clock range (0.1 seconds to 999 minutes); press the "SET" button to set the current The method for the next parameter of the mode is the same as above.
4. After setting the parameters, press and hold the "SET" button for 2 seconds, the current mode will flash once, and then return to the main interface, which means that the parameters have been successfully set.
Main interface: If the relay is not in working state, it will display "000" (without decimal point); if it is in working state, it will have a decimal point.
Mode selection screen: press and hold the "SET" button to enter; after setting is completed, press and hold the "SET" button to return to the main interface.
Relay enable mode:
1. ON: The relay is allowed to conduct during the "OP" conduction time;
2. OFF: The relay is forbidden to conduct and is always closed;
In the main interface, press the "STOP" button to switch between ON and OFF, the current status will flash, and then return to the main interface. (This function is an emergency stop function, press the on button to disconnect the relay)
Sleep mode:
1. "C-P" sleep mode: without any operation for five minutes, the digital display is automatically turned off, and the program runs as usual;
2. "O-d" normal mode: the digital display is always on;
Press and hold the "Stop" button for two seconds to switch between "C-P" and "O-d" status, the current status flashes, and then return to the main interface.
notes:
1. The module is an effective output, and the output voltage is equal to the input voltage.
2.'DC +'and'load +'are internally short-circuited (connected), but'DC-' and'load-' cannot be short-circuited, otherwise the load cannot be switched on and off, which is equivalent to the load being powered up always .
Package list:
1 *Time switch module
Note:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2.Please allow slight manual measurement deviation for the data.
Payment
We accept payment via Paypal only.
Payment must be completed within 5 days. If you have any problems about payment, please contact us via ebay message.
Delivery details
We only
ship to confirmed Paypal addresses.
Please comfirm that your paypal address is in line with your shipping address.
Please kindly note that
the c
ombined shipping
is not provided
because the shipping fee is calculated by weight. Also, the each additional item means
exactly
the the same color and size.
It takes about
7
-15 working days to US; about 10-30 working days to other countries.
Transit time may be a little delayed because of the
bad
weather and customs
inspection
. If you
do
not receive your
item
within 30 working days since payment finished, please contact us immediately for further assistance.
Contact us
We strive for 100% customer satisfaction! Positive Feedback is very important to us. If you have any questions,
p
lease feel free to contact us via "Ask seller a question" . We will reply your email within 24
working hours.